Introduction | Details | Specifications |
Manuals
| White Papers
Parameter Selections
| Input: |
RF or IF 14 |
| |
|
| Channel: |
Television Channels 2 to 62 |
|
Cable Channels 1 to 123 |
| |
|
| Channel Table: |
Broadcast or cable tables |
| |
|
| Channel Lock: |
Locks channel and table |
| |
|
| Headphone Volume: |
200 steps, audio taper |
| Detector AGC Clamp: |
Sync Tip or Back Porch |
| Aural Mode: |
Split or Quasi Parallel |
| Display Language: |
English, Spanish, or French |
| Display Brightness: |
25%, 50%, 75%, 100% |
| Zero Carrier Pulse: |
Line 11 - 36 or OFF |
| Box ID: |
Unique Serial Data Address |
Alarms
All alarms report on front panel display
and output on serial data interface:
RF Too Low
RF Too High
Signal Loss
Visual Loss
Aural
Loss
SAW Temperature Too High
SAW Temperature Too Low
Controls
| Concentric rotary shaft encoders |
2 channels,
Menu (outer knob),
Parameter (Inner knob) |
Display
| Vacuum Fluorescent |
2 lines, 20 characters/line. |
Remote Control
All front panel functions available via
serial data interface. Up to 9 units can be daisy-chained.
AC Mains
| 100/120/220/240 VAC |
50-60Hz, 50 VA ±10% |
Fuse
1/2 Amp, slow blow (MDL) for 100/120 VAC
1/4 Amp, slow blow (MDL) for 220/240 VAC
Size
| 1 Rack Unit |
1.75"H x 19"W x 14"D
44.45 x 482.6 x 355.6 mm |
| |
|
| Aural |
|
Outputs
| Monaural Line |
+10dBm (600 ohm) 25kHz deviation, 75 us deemp
XL-3F connector |
| |
|
| Monaural Headphones |
1.4 volts rms on tip and ring, 1/4" phone
jack" |
| |
|
| Deviation (wideband) |
25mV / kHz into 75 ohm, BNC Connector |
Wideband
| Frequency Response |
+0, -0.8 dB 20Hz - 100kHz at 75 kHz deviation |
| |
|
| Phase Response |
±1.5° 50Hz - 75 kHz |
Stereophonic
| Stereo Separation |
> 40 dB at 10 kHz |
| |
|
| Stereo SNR |
> 55dB 12,13 |
Aural Detector Modes
Split or Quasi Parallel
RF
| Tuning Range |
54.00 - 753.25 MHz |
| |
|
| System |
NTSC-M / North American |
| |
|
| Tuning Tables |
Broadcast: Channel 2-62
Cable STD: Channel 1-123
Cable HRC: Channel 1-123
Cable IRC: Channel 1-123 |
| |
|
| First IF |
955.75 Visual
951.25 Aural
|
| |
|
| Second IF |
45.75 Visual
41.25 Aural |
| |
|
Second IF input/output
(BNC
Connector) |
IF Input Sensitivity: -10 dBm ±3
dB
IF Output Level: -10 dBm
Impedance: 75 ohm |
| |
|
| RF Sensitivity |
Minimum: -48 dBm 2
Maximum: -10 dBm 3
Damage: > +10 dBm 3 |
| |
|
| Return Loss |
> 7 dB @ 75 ohm
> 8 dB @ 50 ohm |
| |
|
| Intercarrier Output |
4.5 MHz / 0 dBm / 75 ohm |
Video
| Video Outputs
(2 BNC Connectors) |
Impedance: 75 ohm
Level: 1 volt peak-peak into 75 ohm |
| |
|
| Frequency Response |
±0.7 dB, 100 kHz to 3.58 MHz 4
±1.0 dB, 3.58 MHz to 4.0 MHz 4 |
| |
|
| Aural Rejection |
> 40 dB, above 4.28 MHz |
| |
|
| Group Delay |
±50 nanoseconds 4,5 |
| |
|
| Signal To Noise Ratio |
NTC-7 > 50 dB -40 dBm RF in
NTC-7 > 55 dB -29 dBm RF in
4.2 MHz unweighted > 50 dB -29 dBm RF in |
| |
|
| Zero Carrier Reference |
Location:
Line 11 to Line 36 off; front panel selectable
Position:
20usec from edge of sync
Width:
30 ±2 usec
Cutoff:
> 48 dB |
| |
|
| IPCM Measurements |
In-Phase Output (I):
1 volt p-p / 75 ohm
BNC Connector
Quadrature Out (Q):
1 colt p-p / 75 ohm BNC Connector |
| |
|
| Linear Distortion |
K Pulse / bar: < 1.0%
K 2T: < 1.5%
Field Time: < 1.0%
Line Time: < 1.0%
Chroma / Lum Delay: 170 ±40 nsec
Chroma / Lum Gain: 100% ±8% at 3.58 MHz
Bounce: Sync < 1%, Blanking < 1%, 100 IRE. |
| |
|
| Nonlinear Distortion |
Luminance Nonlinearity: < 1% p-p
Chroma Nonlinearity: Amplitude < 1%, Phase < 1°
Chroma / Lum Intermod: < 0.5%
Differential Gain: < 1.0%
Differential Phase: < 1.2 |
Notes:
- Input or output selected from front panel.
- Specified video S/N ratio from -40 dBm to -10
dBm.
- This range may be extended with an appropriate
RF attenuator.
- These characteristics are independent of input
level from -40 dBm to -10 dBm, and channel frequency.
- Measured using SINE X / X, relative to North
American M system pre-correction; 200 kHz (reference)
to 4.0 MHz, including ripple.
- Video signal-to-noise ratio measured with aural
carrier present.
- Operation down to an RF input level of -48 dBm
practical with some increase in video noise.
- The I & Q outputs have matched
800 kHz low-pass filters.
- Measured with full field modulated ramp.
- Balanced, transformer coupled.
- Headphone output provided on switchboard quality
tip, ring sleeve (TRS) three wire type phone jack.
Tip and ring sourced separately to drive both ears
of stereo headphones. Either tip or ring may be
shorted as would happen with monaural headphones
using a tip, sleeve (TS) two wire type phone plug.
- Measured using a Modulation Sciences,
Inc. STV-784 Television Stereo Generator and a Modulation
Sciences, Inc. SRD-1 Stereo Reference Decoder. All data
gathered in BTSC Equivalent Mode, quasi parallel detection.
- 0 dB reference = 55 kHz deviation.
- In RF INPUT mode unit receives television channels.
In IF INPUT mode, IF INPUT / OUTPUT BNC connector
switches from being an IF output to being an IF
input. The entire RF input portion is disabled
in IF INPUT mode.
- The serial data interface is modified to permit
daisy-chaining up to 9 units on one circuit. Each
msi 320 has a user assigned address code.
All units supplied with aural notch SAW filter assembly.
|
